Slurry Seal
Find a Contractor/Supplier

Construction Troubleshooting

The following are the most common problems with potential solutions. It may take an investigative approach to determine the actual problem. If you are experiencing a problem not addressed here, consult the ISSA Inspector’s Manual.

IF FINISH TEXTURE IS TOO ROUGH:

  • Discuss with contractor to modify drag being used.
  • Application rate may be too low for the aggregate gradation.
  • Mixure is being placed too dry or is breaking too fast.
  • If using Type III aggregate, it may not be possible to decrease the roughness.

 

IF FINISH TEXTURE IS TOO SMOOTH:

  • Discuss with contractor to modify drag being used.
  • Application rate may be too high for gradation.
  • Excess liquids may be floating the asphalt emulsion to the top.

 

IF DRAG MARKS APPEAR IN FINISH MAT:

  • Aggregate may include oversized material, improve stockpile quality control and screen aggregate if not already doing so.
  • Material may be built up, scrape pugmill and spreader box more often. Clean pugmill and spreader box daily at a minimum, and more often as needed to provide a proper application.
  • Mix may be breaking too quickly, use additive to slow down the break and set of the material.
  • Mixture may be building up on the drag, replace with a new drag.

 

IF EXCESS LIQUID IS COMING OUT OF THE SPREADER BOX:

  • If a test strip was placed successfully, determine what condition changed since then.
  • Decrease water content added to the mix.
  • Verify paver is set to the proper ratios as specified in the Job Mix Formula (Mix Design).
  • Decrease the amount of water used to fog the pavement.

 

IF MIX IS BREAKING TOO FAST, INCLUDING SETTING UP IN THE CORNERS OF THE SPREADER BOX:

  • Verify paver is set to the proper ratios as specified in the Job Mix Formula.
  • Understand how the mineral filler affects the mix, it varies with different Job Mix Formulas.
  • Determine how the mix reacts at both the upper and lower end of the mineral filler range specified in the Job Mix Formula.
  • Determine if the aggregate has been contaminated, particularly with soil.
  • Verify the spreader box augers (if used) are not worn excessively, and are turning the right direction.
  • Verify the asphalt emulsion strainer is clean, to ensure sufficient asphalt emulsion flow to the pugmill.
  • Fog the pavement ahead of the spreader box with water.
  • Ensure that the asphalt emulsion is formulated for current temperatures.
  • Check the asphalt emulsion temperature to determine if it is too hot.
  • Check the gradation and sand equivalence of the aggregate.
  • Add retarder (additive) to the mix.
  • Verify the pugmill water delivery system is not clogged in the strainer or pugmill spray hood.
  • Add water to the mix, but ensure the consistency of the mixture is not too wet.
  • Verify the pugmill is running at the proper speed, excessive speed can cause early breaking.
  • Verify the surface is clean, as dust and dirt on the street can cause the emulsion to break.

 

IF MIX IS BREAKING TOO SLOW:

  • Verify paver is set to the proper ratios as specified in the Job Mix Formula.
  • Understand how the mineral filler affects the mix, it varies with different Job Mix Formulas.
  • Determine how the mix reacts at both the upper and lower end of the mineral filler range specified in the Job Mix Formula.
  • Reduce the retarder (additive) being added to the mix.
  • Reduce the water being added to the mix.
  • Ensure that the emulsion is formulated for current temperatures.

 

IF DRY AGGREGATE ON ASPHALT PAVEMENT:

  • Check pugmill/conveyor belt interface, ensure all aggregate is being deposited in pugmill.
  • Check conveyor(s) seals, repair if necessary.
  • On a continuous paver, check the nurse truck/paver interface, ensure all aggregate is deposited in the front hopper.

 

Post-Construction Troubleshooting

IF EXCESSIVE RAVELING:

  • The aggregate may lack sufficient embedment in the matrix caused from insufficient asphalt quantity to hold the larger aggregate.
  • Poor quality aggregates may de-bond from the matrix.
  • The application rate may have been too thin to hold larger aggregates.
  • The matrix may have a lack of fines to fill voids between larger aggregates.
  • Cooler temperature may result in slowing of the cure necessary for traffic.
  • The project may have been prematurely opened to traffic.
  • The project may have been exposed to rain before final cure was achieved.

 

IF EXCESSIVE TIRE MARKS AND SURFACE ABRASION:

  • The base asphalt may have been too soft.
  • Rolling of low traffic areas will properly set the aggregate in the matrix.
  • For subsequent projects, the slurry seal could be placed during cooler weather, to allow a full cure before being exposed to traffic at elevated temperatures.
  • Broadcast sand to help break the bond and friction between the slurry seal and vehicle tires.